Products

These lights fit perfectly on the front bumper of an Explorer and are about the same width as the grill. These are sourced locally and every light passes through our hands before it's shipped to you. They get the job done at a fraction of the cost of the big names.

Covered by a 1 year warranty - If any issues arise, return your light to us!

• 32" 4D High output LED light bar combo beam (Spot + Flood) 
• Extremely bright! Enhanced forward light projection with the new Real 4D reflectors (Patent Pending)
• Military-grade waterproof breather (Regulates pressure inside the bar while keeping moisture out)
• Includes plug & play wiring harness with switch, waterproof DT connectors and mounting hardware
• Waterproof and weatherproof heavy-duty aluminum housing, Impact resistant PC Lens. Designed for extreme conditions.

Here's an easy solution to mount aftermarket bucket seats into your 91-01 Ford Explorer with power seats. Simply unbolt your factory seat from it's frame, bolt in these brackets, and then bolt your aftermarket seats to the brackets. The brackets position the seat about 1" back from the factory location, and all of the power seat options remain funtional (slide front to back/tilt from back or fornt). Seat mounting tabs are spaced at a common 14"x18" such as PRP's.

Includes

(4) .25" Thick Steel Brackets with tabs

Grade 8 Hardware

The Deaver G50e pack for 91-01 Explorers feature 10 leafs, rebound/military wrap, diamond cut ends, anti-friction pads and four piece bolt through retaining clips.

Use with 8.5" shackle for 4" of lift.

***Please contact us prior to ordering to coordinate a delivery in So Cal, or freight shipment options.

Deaver progressive leaf springs are fabricated with high grade 5160 American made steel. The higher leaf count spring allows the use of thinner leaf material that yields a more flexible progressive leaf stack, or pyramid, producing a much smoother spring rate curve throughout the complete suspension cycle. The even, linear compression rate curve of the progressive spring system is the primary key to excellent ride quality.

• Year Range - 91-01
• Fits 2wd & 4x4 Models
• Works with the factory fuel door
• Factory door handles can be modified to wok
• Price is for a 4 total panels (driver/passenger)

* All sales final - No Returns on these products

* Bedsides are raw in finish and require drilling of mounting holes & prep work before being installed and painted.  Buyer understands that fiberglass and/or body filler may need to be added or removed for optimal fit. 

* Fabrication work required for install, these do not bolt on

NO SHIPPING, LOCAL PICKUP IN SAN DIEGO, CA ONLY!

Manufacturing time is typically 4 weeks

• Year Range - 91-01 (Tail light area will need to be trimmed for 95-01)
• Fits 2wd & 4x4 Models
• Factory door handles can be modified to wok
• Price is for a 4 total panels (driver/passenger)

* All sales final - No Returns on these products

* Bedsides are raw in finish and require drilling of mounting holes & prep work before being installed and painted.  Buyer understands that fiberglass and/or body filler may need to be added or removed for optimal fit. 

* Fabrication work required for install, these do not bolt on

NO SHIPPING, LOCAL PICKUP IN SAN DIEGO, CA ONLY!

Manufacturing time is typically 4 weeks

Replace your weak rear shock bar pins with these eliminators on your 1st or 2nd Gen Explorer.  Designed for your rear, upper shock mounts.  They come unpainted.

• Year Range - 91-01
• Price includes a pair of shock mounts

* Free Shipping!

Here's a good way to freshen up the front of your first gen.

• Year Range - 91-94
• Price includes a pair corner lights
• Made with high quality acrylic vs cheap plastic
• Proudly made in Mexico

* Free Shipping!

This is an awesome upgrade for your first gen. Turn your non funtctional corner reflectors into functional corner lights! Available in white or Amber LED.

• Year Range - 91-94
• Price includes a pair corner lights
• Made with high quality acrylic vs cheap plastic
• Built-in white or Amber LED board, no bulbs needed
• Wired for splicing into a switch headlight or parking light
  
• Proudly made in Mexico

* Free Shipping!

A great facelift for your first gen. The turn signal light is all clear with an oem style reflector pattern This package also includes clear corner lights

• Year Range - 91-94
• Price includes 1 pair of all clear front turn signals, & 1 pair of corner lights
• Made with high quality acrylic vs cheap plastic
• Proudly made in Mexico

* Free Shipping!

Here's a great way to add strength to your 1st gen 4x4.  These plates are cut to fit the inner portion of your driver side beam.  Welding required. Manufactured by Brianbuilt Fabrication.

• Year Range - 91-94

* Free Shipping!

• Year Range - 91-94
• Fits 2wd & 4x4 Models
• Price is for a pair (driver/passenger)

* Price is for a pair

* All sales final - No Returns on these products

* Fenders are raw in finish and require drilling of mounting holes & prep work before being installed and painted.  Buyer understands that fiberglass and/or body filler may need to be added or removed for optimal fit.

NO SHIPPING, LOCAL PICKUP IN SAN DIEGO, CA ONLY!

Manufacturing time is typically 4 weeks

• Year Range - 91-94
• Fits 2wd & 4x4 Models
• Price is for a pair (driver/passenger)

* All sales final - No Returns on these products

* Fenders are raw in finish and require drilling of mounting holes & prep work before being installed and painted.  Buyer understands that fiberglass and/or body filler may need to be added or removed for optimal fit.

NO SHIPPING, LOCAL PICKUP IN SAN DIEGO, CA ONLY!

Manufacturing time is typically 4 weeks

Heavy duty motor mounts for the 4.0L OHV engine in 1st Gen Explorers. Manufactured by Brianbuilt Fabrication.

• Year Range - 91-94
• Price includes a pair of motor mounts

* Free Shipping!

Heavy duty transmission mounts for the automatic, A4LD transmission, found in 1st Gen Explorers. Manufactured by Brianbuilt Fabrication.

• Year Range - 91-94

*Free Shipping!

The ultimate lighting upgrade for your first gen. The turn signal light is all clear with an oem style reflector pattern and includes a full LED board that lights up amber! This package also turns your non funtctional corner reflectors into functional corner lights.

• Year Range - 91-94
• Price includes 1 pair of all clear front turn signal lights with built-in amber LED board, & 1 pair of corner lights with built-in white LED board
• Made with high quality acrylic vs cheap plastic
• Built in LEDs, no bulbs needed
• Corner lights are wired for splicing into a switch headlight or parking light
  
• Proudly made in Mexico

* Free Shipping!

Here's a great way to really make your first gen stand out!

• Year Range - 91-94
• Price includes 1 pair of smoke front turn signals, & 1 pair of smoke corner lights
• Made with high quality acrylic vs cheap plastic
• Proudly made in Mexico

* Free Shipping!

These weld it yourself radius arm pivots are cut from 3/16 steel and accept the common 2.625" spacing and 3/4" bolt found with most 1.25" heims. 

• Year Range - 91-94 (also works on any vehicle that has radius arms - Ranger, Bronco, F150, etc)
• Welding required

This suspension system will drastically change the performance of your Explorer. At 4.5” wider per side and 1” forward for better firewall clearance, this kit gets roughly 14” of wheel travel, about twice as much as stock. Both on and off road handling are great, so this kit is perfect for daily driven trucks as well as dedicated off road toys  

Fabrication/cutting is required for installation. Install should be performed by an experienced person. Shock hoop fabrication is required, as well as tabbing the lower arms for shocks, limit straps and bumpstops. 

Upper and lower arms are shipped raw with bushings installed, as well as ball joints pressed in (lower arms) and 1” fk uniballs installed (upper arms) 

Made to order, approximately 8 week lead time. No refunds once order is placed. 

• Year Range - 95-01

Includes

• Uniball upper control arms
• Boxed balljoint lower control arms
• Tierod extenders
• Extended stainless steel braided brake lines
• Extended axles (4x4 Only)

These upper control arms are slightly longer than stock arms to fix negative camber issues associated with lift kits. Weak upper balljoints are replaced with FK 1” uniballs with heat treated machined pins to attach to the spindle. Arms are powdercoated gunmetal grey.

• Year Range - 95-01

• Year Range - 95-01
• Fits 2wd & 4x4 Models
• Price is for a pair (driver/passenger)

* All sales final - No Returns on these products

* Fenders are raw in finish and require drilling of mounting holes & prep work before being installed and painted.  Buyer understands that fiberglass and/or body filler may need to be added or removed for optimal fit.

NO SHIPPING, LOCAL PICKUP IN SAN DIEGO, CA ONLY!

Manufacturing time is typically 4 weeks

Give your Axial SCX24 the attitude it deserves with this Military style star. Sized perfectly to fit on the hood of your Deadbolt and available in red or green.

This product was designed by my 8 year old son and all proceeds go directly to him!

No-Drill A-pillar light brackets are the perfect way to add more lights to your Explorer. Works well with LED pods and even some 4" round lights.  

• Year Range - 91-01
• Price includes a pair of light mount brackets

* Free Shipping!

We highly reccomend to pair these brackets, with the lights found here - Lights! 

These Dana 35 Radius arms & Pivot Boxes work with 4x4 Explorers, Rangers, and Bronco II's, and are a great addition to any suspension system.

A factory frame hole is utilized for the Pivot Box placement and no welding is required for installation.

Kit Includes

Extended Radius Arms

Pivot Boxes

FK 1 1/4″ Heim Joints

Stainless Steel Misalignment Spacers

Jam Nuts

Grade 8 Hardware

Applications

1991-1994 Explorer

1986-1997 Ranger 

1983-1990 Bronco II

NO SHIPPING, LOCAL PICKUP IN SAN DIEGO, CA ONLY!

These brackets were developed to allow vehicles equipped with the Dana 35 TTB, to convert to the full size Dana 44 TTB. They also feature a second pivot location to allow the use of Dana 35 TTB's.

The entire weld it yourself kit contains 20 pieces. 16 pieces are laser cut, .25" steel that are keyed and interlock, and four, 0.125" thick shims are included in this kit. They can be MIG or TIG welded. Minimal beveling is required for proper weld penetration and fitment, and a few simple bend are required that can be done without a press. It is highly recommended to mock up, and fit all parts on the vehicle. 

Pivot points are very close to the factory location, these are not drop down brackets, or intended to be used as a lift kit.

Professional installation, and welding is required.

If you have a loose door panel, these clips will solve it!

As Explorers age, the integrity of their door panel clips deteriorate.  Also, every time that your door panel is pulled, the teeth on these clips are compromised.  Highly recommended on off road trucks, and when installing speakers, fixing windows, or for any reason that your door panel needs to come off.  Secure it right, nice & tight!

• Year Range - 91-01
• Fits front and rear door panels
• Price includes 25 clips

The GFE Standard Cut and Turned beams are a critical component when it comes to building a GoFastExplorer, Ranger, or Bronco. The factory Dana 35/44 beams are modified in the lower ball joint "ear" to correct the camber/caster angles when increasing your ride height by up to 6 inches. Factory pivot brackets are maintained. Great for use with coilovers, or the stock coil buckets with a taller spring. With the right setup, you can achieve 14-17 inches of usable 4x4 wheel travel.

Premium Cut/Turn

This option takes your cut and turned beams to the the next level. All exterior welds in the lower ball joint ear are smoothed to the give the beam a factory appearance. Additional cleanup is perfomed on the modified area of the interior portion of the beam ends. Package these with our uniball pivots for the ultimate set of clean factory appearing modified beams designed purely for off road performance.

Uniball Pivot Package

Add Uniball Pivots to our Standard or Premium Dana 35 and 44 Cut/Turned Beams. This option includes 1" uniballs, cups, snap rings, and spacers. The cups are machined down to allow additional clearance within the beam pivot pocket. The misalignment spacers are also machined down to the correct spacing for any stock or aftermarket beam pivot brackets. Additional plating is added to the back of the beam to box in the uniball cup to the beam. The axle window is opened up to give clearance for a pushed forward wheel base of up to 2" depending on the vehicle and setup.

Core Exchange Program

All pricing is based on us receiving your beams as a core exchange. Beams need to be clean and grease free. You dont need to sand them down to bare metal, but they need to be grease free and sprayed down with brake cleaner. 

NO SHIPPING, LOCAL PICKUP IN SAN DIEGO, CA ONLY!

Peel & stick these GFE die cut decals! 

• 6" or 12"
  
• High Quality White or Black Vinyl
• Built in house - Send over an email for a quote on custom sizes & colors

Don't forget to clean the surface before applying the sticker.

Show off your GFE pride with these slap decals!

• 3 sizes available
• High opacity film that’s impossible to see through
• Fast and easy bubble-free application

Don't forget to clean the surface before applying the sticker.

Peel & stick these GoFast Explorers die cut decals!

• Available in 12" & 24" (24" pictured)
  
• High Quality gloss vinyl
• Built in house - Send over an email for a quote on custom sizes & colors

Don't forget to clean the surface before applying the sticker.

GoFastExplorer's original Hoodie. Clean & simple.

• Many colors to choose from
• Sizes: S - 5XL